FFA -6004 G2 DSP Amplifier
Price excludes VAT
- 4 x 1500 Watts at 2 Ohms
- FFA Class D PWM amplifiers
- Power supply soft start
- High thermal headroom
- Weight – 10kg
In Stock At Supplier. Usually ships in 1-3 business days.
Trade enquiries welcome. Found a lower price? Let us know
FFA four-channel amplifiers
FFA Generation 2 DSP 4 channel amplifiers feature powerful digital signal processing (DSP). The DSP controlled amplifier provides a cost effective solution for sound system design and can be used for installation or temporary sound systems or any high quality amplified audio requirement. The system is controlled by software called FATWARE. The software is intuitive to use and offer the user a toolbox of audio functions to allow many different systems to be designed.
The FFA-6004 G2 DSP amplifier has 4 analogue audio input’s which can be switched to allow connection of AES/EBU signals. Unusually there are 6 audio output channels, 4 assigned to the four channels within the amplifier and 2 aux outputs connected to a pair of male XLR connectors on the rear of the amplifier. These extra processed outputs can be used to drive any other amplifier channels in the system design.
Complex systems can be designed and signals can be routed as required with a signal matrix.
The DSP has powerful dynamics processors which have fully specified compressor/limiters on each audio input. These could be used for system protection against overdrive and also for environmental noise considerations. Each input and output has 2 bands of dynamic EQ in addtion to parametric eq on each input and output.
The DSP is accessed via an Ethercon connector on the rear panel of the amplifier and connected using a CAT5 Ethernet cable direct to a personal computer or via an Ethernet Hub or router. The DSP is password protected and allows the designer to keep interference from unauthorised persons whom may change parameters and either damage the loudspeaker system or exceed set enviromental noise levels.
Features at a glance
- 4 x 1500 Watts @ 4 Ohms
- compressor limiter on each input
- 6 band parametric EQ per input, 8 band parametric per output, low/high shelving, bell, notch filters, phase, band pass
- 2 band dynamic EQ input and output
- Audio input and compressor/limiter
- loudspeaker signal limiting
- cross over filter types 6,12,18,24,48 dB per octave But, Bes, LR
- Delay – up to 2 seconds, (feet, inch, mm, meters, millisecond).
- 4 audio inputs, 6 audio outputs.
- AES/EBU digital input selectable by a switch on the rear panel
- Ethernet network
- DSP defeat switch so that the amplifier easily reverts back to a 4 input analogue amplifier.
- Front panel level trim using analogue potentiometer, front panel LED signal potentiometers.
Medium to larger full range and dedicated bass loudspeakers, bi amplified stage monitor systems, components within large format touring or installation loudspeakers low mid, high mid and HF, 4 ohm drive.
Medium to large full range loudspeakers 10”-15” drivers + 1” 1.5” HF
Low mid, high and HF in larger multi way systems installed or touring.
High power stage monitors 2×12” or 15” +1.5”
Medium bass 2×12” 15” or 1×18”
Use in conjuction with high power bass amplifiers signal driven from auxillary outputs on rear of DSP amplifier.
|FFA – 6004 – 4 x 900W 8 Ohm, 4 x 1500W 4 Ohm|
|THD||Typical 0.05 4 Ohm 1kHz THD+N|
|20Hz – 20kHz +- 0.5dB|
|Controls||40 Point Potentiometer per channel, power on switch|
|Indicators||signal green = -20dB, signal yellow = -3dB, red signal = clip, signal red protect = over current, low AC mains or 3 sec. mute on power up|
|DC on output, side-chain TCA clip limiter circuit|
|Short circuit, current overload, thermal shutdown, high-frequency stability circuit|
|Balanced Neutrik® Female XLR input connected Pin 1 – GND, Pin 2 – Hot +, Pin 3 – Cold -. XLR Male signal throughput each channel|
|Neutrik® speakON each channel. Channels 1 and 3 output speakON utilizes 2+ and 2- connection to allow the use of 4 core loudspeaker cable for bi-amp loudspeaker system, for example, stage monitor system|
|1 x Neutrik® 20A powerCON connector 1 x 16A 230 VAC Circuit. Power range 185V-230VAC
120V (configured at the factory)
|High CFM 80mm fan with proportional signal speed control. Rear to front airflow|
|Dimensions||88mm Height x 483mm Width x 510mm Depth. Includes rear rack support. 19″ rack-mount enclosure|
|Delivery & Returns||
Free Delivery on all orders over £99 plus VAT.
Your purchase will usually be with you within 3 working days of your order being placed.
If you are in the Scottish Highlands, Northern Ireland, Isle of Man and the Channel Isles you will still get free delivery but your order may take up to 6 working days to get to you.
Please note: Delivery times pending stock availability.
-I need my products quickly- can you help?
Absolutely! Please give us a call and we'll do our best to get your items to you quickly
-When is the cut off for Next day delivery?
If you place your order before 2 pm Monday- Friday, we will dispatch the same day.
Our returns department aims to help you as quickly as possible with any issues you may have with your product.